Marinette Boat Marinette Forum and Site

  • Skip to content
  • Jump to main navigation and login
  • Jump to additional information

Nav view search

Navigation

  • Big M's Rule !!
  • Engines
  • Hull and Paint
  • Forum
  • Gallery
  • Electrical and Electronics
  • Sites we like
  • Store

Search

You are here: Home Store

Popular Tags

  • Marinette

Latest Articles

  • The forum user control panel
  • Galvanic Isolator
  • Old forum notes on Antifouling and Bottom Painting
  • Old forum notes on Miscellaneous Engine Topics
  • Old forum notes on engine troubleshooting

Marinette Boat forum feed is closed

Marinette Boat Forum

18 June 2021

A forum for aluminum boat owners and those directly supporting them
  • Electrical and Electronics • Re: Pertronix distributors
    Thanks, Jeff. I have checked that several times and am sure I am all good. Last night I removed the all the old ignition parts (ballast resistor, brain box). Timing was off. Had to advance it about 2 or 3 deg to get the backfire eliminated. Seems to running good now. Few more lake tests this weekend to be sure.

    Statistics: Posted by MissConduct — Fri Jun 18, 2021 6:24 am

  • Electrical and Electronics • Re: Pertronix distributors
    Before you start changing things, make sure the plug wires are going to the right plugs. Seriously! The way the wire dive between the manifolds and heads makes it easy to cross a few wires. An insurance company mech playing with mine did that and it took me a while to straight his damn mess out!

    Here's the best way to do it: Warm the motor up. With insulated gloves, remove one wire at a time from the distributor cap. If the motor slows, put it back. If it does not, leave it out and keep pulling wires. If you find a second wire doing the same thing, swap the two wires.

    Let's hope that's all that's wrong here.

    Jeff

    Statistics: Posted by Fastjeff — Thu Jun 17, 2021 5:28 pm

  • Paint • paint
    Question for Mike Ray. Years ago you tried Rust-oleum marine paint on a 26 0r 28 I think.
    How did it last?
    Wayne

    Statistics: Posted by ddependo — Thu Jun 17, 2021 2:23 pm

  • Electrical and Electronics • Pertronix distributors
    Just purchased an 82 32 sedan. Previous owner told me he put Petronix distributors in 2019. Could not water test boat before I purchased. Finally got in the water and having lots of backfiring through the carb. Have rebuilt carbs, put new wires, plugs, cap and rotor. I am down to thinking he left too much of the old ignition system in place. Ballast resistor still hooked up as well as brain box. Any advice on what needs to be left. I believe both could be eliminated besides maybe tach wire. Thoughts?

    Statistics: Posted by MissConduct — Thu Jun 17, 2021 12:19 pm

  • About My Boat Brags • Re: Water on floor in salon
    Wkeller2010 The boat is a 32', 1989 Sedan Fly Bridge. You have been a member since 2015 how's about adding a signature to your posts...bill
    Bill: consider adding a primer..he may not know how to add signature..

    Statistics: Posted by jralbert — Mon Jun 14, 2021 9:58 am

  • About My Boat Brags • Re: Water on floor in salon


    Wkeller2010

    The boat is a 32', 1989 Sedan Fly Bridge.

    You have been a member since 2015 how's about adding a signature to your posts

    How do I add a signature to my post?

    To add a signature to a post you must first create one via your User Control Panel. Once created, you can check the Attach a signature box on the posting form to add your signature. You can also add a signature by default to all your posts by checking the appropriate radio button in the User Control Panel. If you do so, you can still prevent a signature being added to individual posts by un-checking the add signature box within the posting form.

    bill

    Statistics: Posted by bill — Mon Jun 14, 2021 8:57 am

  • About My Boat Brags • Re: Water on floor in salon
    Water may be pooling and falls backwards through ?? to below.

    Jeff

    Statistics: Posted by Fastjeff — Mon Jun 14, 2021 6:54 am

  • About My Boat Brags • Re: Water on floor in salon
    Ahh...drain plugs not tight..thru hull taking in water..loose hose. Have you checked the bilge to see whether you've got water down there...hull crack in a place that's under pressure while you're underway. Forget all the stuff on screws and windows (altho checking window drainage is good general advice).

    When you're on plane, bilge water accumulation should be near stern because of angle.

    Suggest you have hatches open and have someone inspecting below while you're underway

    Statistics: Posted by jralbert — Sun Jun 13, 2021 11:04 pm

  • About My Boat Brags • Re: Water on floor in salon
    In my initial post I failed to mention, when the water appears, it’s only when we’re on plane. Again, it’s appearance is very random. I cannot figure out where this volume of water could be stored. We’re in a covered slip so rainwater should not be an issue. I thought perhaps there’s a loose hose connection, or bad hose, at the water tank but I’ve not found water on top, or below, the tank.

    Statistics: Posted by Wkeller2010 — Sun Jun 13, 2021 6:21 pm

  • About My Boat Brags • Re: Water on floor in salon
    I'm guessing you have a screw loose. No, not in THAT way. But above in the cabin roof/flybridge floor and water is migrating along its preferred path. Suggest removing headliner and seeing that you can see. Next culprit might be windows with blocked drains. These thins are often mysterious and hard to track but some detective work will lead you to the source eventually.

    If it is a loose (or missing) screw or two, easy to remedy: Caulk the hole, wait til it sets a while, tighten the screw.

    Good luck!!

    Statistics: Posted by jralbert — Sun Jun 13, 2021 10:32 am

  • About My Boat Brags • Water on floor in salon
    Curious if anyone has had this issue or has an idea where the water is coming from. The boat is a 32', 1989 Sedan Fly Bridge.

    We’ve recently had water on the floor in the salon. It’s coming from inside the helm’s wiring and control cables locker. The ‘floor’ in there is wet. This doesn’t happen all the time, and when it does, it’s either barely noticeable, or the carpet is soaked in a 3’ x 3’ area in the center of the salon. The wiring above the floor in the wire locker isn’t wet. The water tank is directly below this locker. No water below the water tank or in the engine compartment. Any thoughts or suggestions?

    Statistics: Posted by Wkeller2010 — Sun Jun 13, 2021 8:57 am

  • General Topics • Re: Number of Boats' built ?
    David,
    As previously mentioned, a change from the original thread subject (in this case - " Number of Boats built?) warrants the start of a new thread subject >> or continuation of a previous one <<. This allows for continuity of the subject. Even an old thread can be picked up on and additional questions / info added. And an old thread may contain the answers (or portions thereof) to a question/inquiry. In the case you asked about just above, you could start/add to a thread relative to "Flybridge Electrical Question"

    Bill

    Statistics: Posted by bcassedy — Thu Jun 10, 2021 7:12 am

  • General Topics • Re: Number of Boats' built ?
    That flybridge stuff gets exposed to corrosion far more than the stuff inside the cabin. I suspect that's your problem, and I feel for you since 'cause I HATE electrical problems! You'll have to take it wire by wire, switch by switch, to clear everything up.

    Good luck!

    Jeff

    PS: And people ask me why I removed my flybridge!

    Statistics: Posted by Fastjeff — Thu Jun 10, 2021 6:48 am

  • General Topics • Flight/ upper bridge controls
    Thanks For the answer on the gph question…. Now does anyone know how to get the upper bridge switches to work? Is there some secret on Marinettes that I’m not aware of…. I cannot get the ignition to crank or turn off from the upper bridge.

    Statistics: Posted by David — Tue Jun 08, 2021 10:35 pm

  • Electrical and Electronics • Re: Removing carbureator
    Most gas powered marine generators have electric fuel pumps. If yours does you need to make sure it is powering up while cranking. A test light will tell you if you have power to it.

    Statistics: Posted by EWRice — Tue Jun 08, 2021 11:50 am

  • Login Form

Only for authorized article submitters.

  • Forgot your password?
  • Forgot your username?

Welcome


Categories

Forum Support

Featured products

$9.95
Details
Marinette Boat Forum Support
This is a item to help support the Marinette Boat Forum. More products and items for our Big M's will be coming !!!
Close info

Additional information