Packing Boxes
Packing Boxes
a source for packing boxes for rudder and shaft.
http://www.deepblueyachtsupply.com/driv ... e-assembly
bill
Last edited by bill on Fri Mar 27, 2015 1:23 pm, edited 1 time in total.
Former owner of
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
Re: Packing Boxes
Hi Bill, I was just looking at that yacht supplies offerings and see that they offer non-metallic cutlass bearings. I just had the boatyard press a new bearing in the starboard strut and they used a bronze bearing. My question is weather a non-metallic is important enough to go through the time and expense of changing it out. Thanks
1987 32 f/b sedan with twin 318's Docked on florida's nature coast
Re: Packing Boxes
You're not going to like this, but you're going to have to have that bronze bearing replaced. Failure to do so is going to result in a lot of corrosion, major type! Only a non-metallic bearing is to be used. Sorry....
Bill
Bill
Bill & Sharon Cassedy
"Sunset Seeker"
'88 32' Sedan Bridge to be sold (updtd 1-1-22)
"Sunset Seeker Too" (SS2)
'88 41' Marquis hardtop. (as of 1/1/22)
Located in Aurora, In.
Always fresh water.
"Sunset Seeker"
'88 32' Sedan Bridge to be sold (updtd 1-1-22)
"Sunset Seeker Too" (SS2)
'88 41' Marquis hardtop. (as of 1/1/22)
Located in Aurora, In.
Always fresh water.
-
- Site Admin
- Posts: 410
- Joined: Sat Jul 12, 2014 6:18 am
- Location: Kentucky
Re: Packing Boxes
YUP they gotta go! Will be a VERY expensive fix if they are left in and in the water for any length of time.
Safe boating,
dave
Safe boating,
dave
1987 Marinette 29 FB Sedan
Retired Boat Accident UL and USCG trained investigator
Retired USCG Captain
Retired Boat Accident UL and USCG trained investigator
Retired USCG Captain
Re: Packing Boxes
To all the replies above, I say Amen. I am reluctant to say this - but will anyway - you have to question the people at the boat yard who thought putting a metal bearing in an aluminum boat was the right thing to do. It should make you think twice about future advice you receive from them. You did the right thing, though, by raising the question here.
-joel-
former owner 1988 '32 FB Sedan
Chesapeake Bay
twin 318 / 240 hp
Potomac MD
former owner 1988 '32 FB Sedan
Chesapeake Bay
twin 318 / 240 hp
Potomac MD
Re: Packing Boxes
I will let the following pictures answer this question. This also goes for having your shaft isolated.
If you keep the metal cutlass you will be shipping what is left of your strut to Pluckebaum to get a new one made. I just shipped mine off today. I will also be installing drive savers so I don't need to worry about my shaft isolation anymore.
If you keep the metal cutlass you will be shipping what is left of your strut to Pluckebaum to get a new one made. I just shipped mine off today. I will also be installing drive savers so I don't need to worry about my shaft isolation anymore.
1973 Marinette Seacrest Executive
41x14
Twin Chrysler 340's with Velvet Drive 71C
"Figment"
41x14
Twin Chrysler 340's with Velvet Drive 71C
"Figment"
Re: Packing Boxes
Thanks guys for the input, it's only money right. Those pictures of that strut are very convincing.
1987 32 f/b sedan with twin 318's Docked on florida's nature coast
Re: Packing Boxes
Yes to all the above.
The fiber cutless bearings are about $40 each. You don't need to pay to have them pressed in. Get about 12 inches or so of half inch all thread, washers and nuts to fit. Back off set screws if you have them, clean up the strut, lube the bearing and squeeze it in with the all thread and nuts. Will take $4.00 for the all thread and five minutes to do it. One of the easier jobs you will have.----Ed
The fiber cutless bearings are about $40 each. You don't need to pay to have them pressed in. Get about 12 inches or so of half inch all thread, washers and nuts to fit. Back off set screws if you have them, clean up the strut, lube the bearing and squeeze it in with the all thread and nuts. Will take $4.00 for the all thread and five minutes to do it. One of the easier jobs you will have.----Ed
BUSIA
located in Ketchikan, Alaska. Gods country
32 foot Marinette (no fly bridge)
twin 350 Crusader (Chev 350) engines
1:1 Borg Warner velvet drive transmissions
Closed cooling (antifreeze in the engine)
Proud to be retired IBEW and an A+P
located in Ketchikan, Alaska. Gods country
32 foot Marinette (no fly bridge)
twin 350 Crusader (Chev 350) engines
1:1 Borg Warner velvet drive transmissions
Closed cooling (antifreeze in the engine)
Proud to be retired IBEW and an A+P
-
- Tin star
- Posts: 41
- Joined: Mon Jul 14, 2014 9:51 am
Re: Packing Boxes
I recommend always using Set Screws with Cutless Bearings. I have seen them spin up the shaft. (or down depending on engine rotation.)
New Endeavor
1991 41ft Aft Cabin
Louisville,Ohio River
1991 41ft Aft Cabin
Louisville,Ohio River
Re: Packing Boxes
I wanted to add and thank you Bill for the vendor recommendation Deep Blue Yacht Supply. They have supplied bearings, packing boxes, dripless shaft seals, seacocks, and now new shafts and plates. They are competent, competitive and the service is incredible. I have spent time on the phone, emailed photos, and in general talked through my project with them. I only hope business is fabulously successful for them.
Calivanos
1964 31' Marinette Cabin
Twin V6 Vortecs, ZF Hurth Transmissions
Matagorda, Texas
1964 31' Marinette Cabin
Twin V6 Vortecs, ZF Hurth Transmissions
Matagorda, Texas