Cooling parts for Chryslers
- Details
- Category: Marinette Engines
- Published: Monday, 14 July 2014 16:29
- Written by Super User
- Hits: 8955
These are some of the pesky riser parts
Hint: Take (or borrow) a laptop to the boat. and go to a site with a very good catalog (or print out), save the web page so you can see the parts as you need them. I put the parts I used with location and catalog numbers on a page.
Order the riser and elbow parts ahead of time, these are the parts I used to replace everything except the manifold, from http://www.marineengineparts.com who I endorse. You may need more "plugs" than come with the riser.
I'll assume you just bought your boat. How to tell if you have a freshwater or raw water systems, 1) look for a plastic radiator fluid cooling bottle or 2) look for a radiator cap on a big metal tube (a heat exchanger). Fresh water systems use antifreeze in the engine block, and raw water systems use river water in the engine block to cool the system.
Raw water systems are common and not as much of an issue as some might think. (My previous boat had raw water cooled engines that were more than 25 years old. My new boat has a fresh water system. Hint: The end gaskets on a old style heat exchange match the mercruiser part.
Important
Tip #1 for newbies. Like wiring, replace each hose one at a time. Don't yank them all off. |
|
Tip #2 If you don't know... expect to replace all the fittings and buy them ahead of time. |
|
Tip #3 Somebody else's engine is not yours. Don't assume, look and see before you order. I have a box full of perfectly good ass-a u and me parts. It's harder to find the parts than it is to fix them. |
|
Tip #4 Take a camera and laptop to the boat. Write down the parts you buy and that fit. Snap pictures, as you'll have forgotten in 2-3 years. Don't order from someone that does not know Chryslers, Crusaders or your engine in detail. |
|
Tip #5 Keep the invoices in a folder. |
|
Tip #6 Cheap hoses and clamps bite... don't use them. |
Finally decide what you plan to replace... remember safe, then reliable, then cosmetic. Cooling is a safety issue.
http://www.marineengineparts.com
Courtesy of the part man (Gregg of Lighthouse Marine).
Chrysler Swivel Elbow
CM-20-4142411
Replacement Swivel Elbow for Chrysler part #'s 3745639, 2847623, 2847404, and E9223M. Includes all pipe plugs. 3 Year warranty. I needed 2.
Chrysler Mounting Kit - OSC480-MK-FW
OSC480-MK-FW
End Plate/Riser/Elbow Mounting Kit for OSC826 Manifold. Used on FRESHWATER Applications. The Raw water ones have holes in the top.
Fresh Water Cooled Applications. Fits OSC0402, OSC106, OSC106T, OSC689, OSC794 & OSC639.
CHRYSLER LOWER SWIVEL-318/340/360
CM-20-2600402
LOWER ELBOW FOR 318 / 360. TO CONNECT TO SWIVEL ELBOW.
SWIVEL ELBOW MOUNTING KIT
$27.30
CM-20-4142411PKG
SWIVEL ELBOW MOUNTING KIT FOR ELBOW # CM-20-4142411.
Chrysler Swivel Elbow | CM-20-4142411 |
CHRYSLER LOWER SWIVEL-318/340/360 | CM-20-2600402 |
SWIVEL ELBOW MOUNTING KIT | CM-20-4142411PKG |
Unless you have done this before, it's easy to damage the O-rings when you install. So order an extra O-ring.
From Fittings and More - 360 Fresh water cooled hose barbs http://www.fittingsandmore.com/
For each engine, I used the following ... 360 Fresh water cooled hose barbs
360 Fresh water Temp Sensor plug |
|||||||||||||||
If needed... |
28111*
|
3/4 X 1/2 MIP X FIP BS BUSHING - For Temp Sensor
|
1
|
44634*
973-965
|
3/4 PLUG
3/4 Bronze tee (HOSE FITTING Section not in the Tees)
|
4
2
|