Search found 26 matches
- Thu Jun 25, 2020 1:13 pm
- Forum: Engines
- Topic: Fuel prime
- Replies: 11
- Views: 26034
Re: Fuel prime
I have had the anti syphon valve for the generator stick several times. They locate them right off the top of the tank, threaded onto a nipple coming out of the tank. Also make sure you have no leaks along the fuel lines. A pinhole can suck in enough air to stop the draw of fuel. Good luck
- Sat Apr 11, 2020 7:17 pm
- Forum: Cabin and Interior
- Topic: Sliding cabin screens
- Replies: 15
- Views: 35987
Re: Sliding cabin screens
Got the screen corner rollers from swisco. They appear stronger and better made than the original hardware. They are not crap and didn't strip out when adjusted.
- Thu Apr 02, 2020 1:10 pm
- Forum: Cabin and Interior
- Topic: Sliding cabin screens
- Replies: 15
- Views: 35987
Re: Sliding cabin screens
After doing research on screen door rollers and not coming up with much, someone on the FB site commented that Swisco sells the replacement corner rollers. They were correct $3.50 each, what a deal
- Tue Sep 10, 2019 6:48 pm
- Forum: Engines
- Topic: New oil pump?
- Replies: 7
- Views: 27300
Re: New oil pump?
Mopar performance at one time sold a 5/16 hex shaft that would slide down the hole for the intermediate shaft and into the oil pump. The engine could be tested to make sure you have oil pressure by running a drill motor on the shaft to prime and test the motor for oil pressure. This could be done be...
- Sun Jul 28, 2019 4:08 pm
- Forum: Engines
- Topic: Exhaust manifold tubes
- Replies: 3
- Views: 12701
Exhaust manifold tubes
I am replacing a leaking manifold/riser/swivel elbow on my 360 Chrysler. It has the log style manifolds with exhaust to the rear. The original manifold was installed with the water tube and had the water entering the front of the manifold at the water tube. My new manifold (Barr) instructions says t...
- Sat Feb 16, 2019 12:56 pm
- Forum: Engines
- Topic: Oil leak without engine running?? Any ideas?
- Replies: 2
- Views: 12072
Re: Oil leak without engine running?? Any ideas?
Check the front drain on the oil pan sump, my boat has a small ball valve installed, not sure if this was original equipment or added later. Check your oil filter for leakage. Oil could also be from a cooling line from the velvet drive transmission, or the trim tab reservoir.
- Sun Oct 07, 2018 7:12 pm
- Forum: Props
- Topic: Prop size and operating RPM for 318 Chrysler engines
- Replies: 15
- Views: 39101
Re: Prop size and operating RPM for 318 Chrysler engines
What was your speed and rpm with the old props
- Mon Jul 03, 2017 10:53 am
- Forum: Boat and Hull
- Topic: hull repair
- Replies: 16
- Views: 25135
Re: hull repair
Was the garbage truck totalled?
- Fri Jun 30, 2017 12:59 pm
- Forum: Boat and Hull
- Topic: source for: rub rail
- Replies: 2
- Views: 7393
Re: source for: rub rail
Doug Doty had a run of rub rail extruded a couple of years ago. He is a member on this sight. See if he has any left
- Thu Jun 23, 2016 3:36 pm
- Forum: Drivetrain
- Topic: 318 "302" heads.....
- Replies: 10
- Views: 25490
Re: 318 "302" heads.....
I believe that the 302 heads came out in the mid 1980's. My father in law had a 28' big M at the time with a tired 318. We pulled the motor, freshened up the bottom end with a .030 over bore, balanced, upgraded rod bolts and the "302" heart shaped combustion chambered heads. The upgrade wa...